FluoroPel Polymer Solutions and Inks
Note: See Fluorothane for hydrophobic
and
super-hydrophobic aircraft, marine and ground radome coatings. See FluorN
for fluorosurfactants and FluoroSyl for
flluorosilanes.
Samples may be obtained nationally and internationally by
providing
a FedX account number to cover shipping. Bulk pricing upon request.
FluoroPel
products are RoHS & WEEE
compliant.
Statement about PFOA and PFOS.
Clear FluoroPel Solutions
PFC 501A, 502A & 504A are one, two and four percent
fluoropolymer
solutions in low boiling point fluorosolvent (BP=56°C). Thin films
dry in seconds at room temperature to a surface energy of about 10
dynes/cm.
Warming to 90°C for 10 minutes optimizes adhesion and reduces the
surface
energy to about 6 dynes/cm. PFC500-series solutions may replace 3M
FC722
and EGC-1700 and are recomended for dip application. The no charge
addition
of 2 percent fluorosilane or fluorophosphate is recommended for
application
to oxide surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available. MSDS
PFC 504A-coFS is a four percent fluoro-silane copolymer
solution
(BP=84°C) for coating glass, ceramic and metal surfaces. Thin films
dry in a few minutes and bond after a few minutes at 120° C or
after
24 hours at room temperature. Surface energy of the cured film depends
on
the substrate and can vary between 6 and 10 dynes/cm. Application by
dip.
$206 per pound; 1, 5, 15 & 30 gallon pricing available. MSDS
PFC 504A-coE5 is a four percent fluoro-epoxide oligomer in
a
low boiling point fluorosolvent (BP=56°C) having good adhesion to
many
substrates. Coatings may be cured using amines, anhydrides or catalysts
(thermal or UV). Surface energy of cured films can vary between 6 and
10
dynes/cm. Epoxy equivalent weight is 2800. Epoxy silanes at 1-2% are
recommended
on oxide surfaces.
$206 per pound; 1, 5, 15 & 30 gallon pricing available.
PFC 501AFA, 502AFA & 504AFA are one, two and four
percent
fluorinated copolymer solutions in fluorosolvent (BP=56°C) that are
optimized for adhesion to plastics such as vinyl and polycarbonate.
Thin
films dry in seconds at room temperature to a surface energy of about
10
dynes/cm. Warming to 90°C for 10 minutes optimizes adhesion and
reduces
the surface energy to about 6 dynes/cm. May not be resistant to
somenpolar
organic solvents.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 501IBA, 502IBA & 504IBA are one, two and four
percent
fluorinated copolymer solutions in fluorosolvent (BP=56°C) that
have
good adhesion to many plastics and metals. Thin films dry in seconds at
room temperature to a surface energy of about 10 dynes/cm. Warming to
90°C
for 10 minutes optimizes adhesion and reduces the surface energy to
about
6 dynes/cm. PFC500-series solutions may replace 3M FC722 and EGC-1700
and
are recomended for dip application. The no charge addition of 2 percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 501LMA, 502LMA & 504LMA are one, two and four
percent
fluorinated copolymer solutions in fluorosolvent (BP=56°C) that
have
good adhesion to many plastics and metals. Thin films dry in seconds at
room temperature to a surface energy of about 10 dynes/cm. Warming to
90°C
for 10 minutes optimizes adhesion and reduces the surface energy to
about
6 dynes/cm. PFC500-series solutions may replace 3M FC722 and EGC-1700
and
are recomended for dip application. The no charge addition of 2 percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 501TFH, 502TFH & 504TFH are one, two and four
percent
fluorinated copolymer solutions in fluorosolvent (BP=56°C) that
have
good adhesion to many plastics and metals. Thin films dry in seconds at
room temperature to a surface energy of about 10 dynes/cm. Warming to
90°C
for 10 minutes optimizes adhesion and reduces the surface energy to
about
6 dynes/cm. PFC500-series solutions may replace 3M FC722 and EGC-1700
and
are recomended for dip application. The no charge addition of 2 percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 601A, 602A & 604A are one, two and four percent
fluoropolymer
solutions in 3M HFE 7100 fluorosolvent (BP=61°C). Thin films dry in
seconds at room temperature to a surface energy of 8-10 dynes/cm.
Warming
to 90°C for 10 minutes optimizes adhesion and reduces the surface
energy
to about 6 dynes/cm. PFC602A may replace 3M 722
and
EGC-1700 and is recomended for dip application. The no charge
addition
of 2 percent fluorosilane or fluorophosphate is recommended for
application
to oxide surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.MSDS
PFC 601AFA, 602AFA & 604AFA are one, two and four
percent
fluorinated copolymer solutions in 3M HFE 7100 fluorosolvent
(BP=61°C)
that are optimized for adhesion to plastics such as polycarbonate. Thin
films dry in seconds at room temperature to a surface energy of about
10
dynes/cm. Warming to 90°C for 10 minutes optimizes adhesion and
reduces
the surface energy to about 6 dynes/cm. PFC600-series solutions may
replace
3M FC722 and EGC-1700 and are recomended for dip application. The no
charge
addition of 2 percent fluorosilane or fluorophosphate is recommended
for
application to oxide surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 601IBA, 602IBA & 604IBA are one, two and four
percent
fluorinated copolymer solutions in 3M HFE7100 fluorosolvent.
(BP=61°C)
that have good adhesion to many plastics and metals. Thin films dry in
seconds
at room temperature to a surface energy of about 10 dynes/cm. Warming
to
90°C for 10 minutes optimizes adhesion and reduces the surface
energy
to about 6 dynes/cm. PFC600-series solutions may replace 3M FC722 and
EGC-1700
and are recomended for dip application. The no charge addition of 2
percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 601LMA, 602LMA & 604LMA are one, two and four
percent
fluorinated copolymer solutions in 3M HFE7100 fluorosolvent
(BP=61°C)
that have good adhesion to many plastics and metals. Thin films dry in
seconds
at room temperature to a surface energy of about 10 dynes/cm. Warming
to
90°C for 10 minutes optimizes adhesion and reduces the surface
energy
to about 6 dynes/cm. PFC600-series solutions may replace 3M FC722 and
EGC-1700
and are recomended for dip application. The no charge addition of 2
percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 601TFH, 602TFH & 604TFH are one, two and four
percent
fluorinated copolymer solutions in 3M HFE7100 fluorosolvent
(BP=61°C)
that have good adhesion to many plastics and metals. Thin films dry in
seconds
at room temperature to a surface energy of about 10 dynes/cm. Warming
to
90°C for 10 minutes optimizes adhesion and reduces the surface
energy
to about 6 dynes/cm. PFC600-series solutions may replace 3M FC722 and
EGC-1700
and are recomended for dip application. The no charge addition of 2
percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 11 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 801A, 802A & 804A are one, two and four percent
fluoropolymer
solutions in fluorosolvent (BP=84°C). Thin films dry in minutes at
room temperature to a surface energy of about 10 dynes/cm. Warming to
90°C
for 10 minutes optimizes adhesion and reduces the surface energy to
about
6 dynes/cm. PFC802A may replace
3M FC722 and EGC-1700
and is recomended for dip application. The no charge addition of 2
percent
fluorosilane or fluorophosphate is recommended for application to oxide
surfaces.
1 to 13 pounds $70, $115 and $206 per pound; 1, 5, 15 & 30 gallon
pricing
available. MSDS
PFC 1301A, 1302A & 1304A are one, two and four
percent
fluoropolymer solutions in low boiling point fluorosolvent
(BP=135°C).
Thin films dry in a few hours at room temperature to a surface energy
of
about 10 dynes/cm. Warming to 90°C for 10 minutes optimizes
adhesion
and reduces the surface energy to about 6 dynes/cm. PFC1300-series
solutions
may replace 3M FC722 and EGC-1700 and are recomended for spray or spin
application.
The no charge addition of 2 percent fluorosilane or fluorophosphate is
recommended
for application to oxide surfaces.
1 to 13 pounds $95 , $140 and $240 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 1301IBA, 1302IBA & 1304IBA are one, two and
four percent
fluorinated copolymer solutions in fluorosolvent (BP=135°C) that
have
good adhesion to many plastics and metals. Thin films dry in seconds at
room temperature to a surface energy of about 10 dynes/cm. Warming to
90°C
for 10 minutes optimizes adhesion and reduces the surface energy to
about
6 dynes/cm. PFC1300-series solutions may replace 3M FC722 and EGC-1700
and
are recomended for spray or spin application. The no charge addition of
2 percent fluorosilane or fluorophosphate is recommended for
application
to oxide surfaces.
1 to 13 pounds $95 , $140 and $240 per pound; 1, 5, 15 & 30 gallon
pricing
available.
PFC 1601A, 1602A & 1604A are one and four percent
fluoropolymer
solutions in high boiling point fluorosolvent (BP=160°C). Thin
films
dry in 2-3 hours at room temperature to a surface energy of about 10
dynes/cm.
Warming to 90°C for 10 minutes optimizes adhesion and reduces the
surface
energy to about 6 dynes/cm. PFC1600-series solutions may replace 3M
FC722
and EGC-1700 . The no charge addition of 2 percent fluorosilane or
fluorophosphate
is recommended for application to oxide surfaces. Application by spray,
brush, ink jet, pad print or spin. Boeing777
MT 34-023.pdf
1 to 13 pounds $95 , $140 and $240 per pound; 1, 5, 15 & 30 gallon
pricing
available. MSDS
PFC 1601V is a one percent fluoropolymer solution in
fluorosolvent
(BP=160°C). Thin films dry in 4-6 hours at room temperature to a
surface
energy of about 16 dynes/cm. Heating to 180°C for 30 minutes
optimizes
adhesion and reduces the surface energy to about 14 dynes/cm. PFC1601V
is
recomended for spin, spray or blott applications where extreme UV
resistance
is needed. The no charge addition of 2 percent fluorosilane or
fluorophosphate
is recommended for application to oxide surfaces.
$201 per pound; 1, 5, 15 & 30 gallon pricing available
PFC 1604V is a four percent fluoropolymer solution in
fluorosolvent
(BP=160°C). Thin films dry in 4-6 hours at room temperature to a
surface
energy of about 16 dynes/cm. Heating to 180°C for 30 minutes
optimizes
adhesion and reduces the surface energy to about 14 dynes/cm. PFC1601V
is
recomended for spin, spray or blott applications where extreme UV
resistance
is needed. The no charge addition of 2 percent fluorosilane or
fluorophosphate
is recommended for application to oxide surfaces.
$152 per 100 grams; $664 per pound; 1, 5, 15 & 30 gallon pricing
available
PFC M1604V is a four percent fluoropolymer solution in
fluorosolvent
(BP=160°C). Heating films to 180°C for 30 minutes produces
solvent
and uv resistant films with 150° contact angles to water. PFC1601V
is recomended for spin, spray or blott applications where extreme UV
resistance
is needed. Application by spray, brush, ink jet, pad print or spin.
$240 per pound; 1, 5, 15 & 30 gallon pricing available.
PerFluoroCoat Inks
PFC GH-Series hydrophobic inks are translucent or pigmented.
Thin
films cure in 30 minutes at 180°C, have 120° contact angles to
water., and have good chemical resistance
$650 per pound.
PFC MH-Series super-hydrophobic screen inks are translucent or
pigmented.
Thin films cure in 3 minutes at 200°C, have contact angles to water
in excess of 150° , and have good chemical resistance.
$650 per pound.
FluorN, FluoroSyl, FluoroPel, Fluorothane and PerFluoroCoat are
trademarks
of the Cytonix Corporation. Patents
are issued or pending
for the formulations listed on this page, for certain methods of their
application
, and for the coating of certain articles. Copyright 1997.
Cytonix Corporation
8000 Virginia Manor Road
Beltsville, MD 20705
phone: (888) CYTONIX
fax: (301) 470-6269
